|
|
|
|
|
|
|
|
|
|
|
|
|
|
We designed this tarp to be a heavy-duty, but still economical solution for covering your 26M in the off-season. It is custom cut and reinforced, made of 12-mil tarp material which much thicker than cheap hardware store tarps. It has grommets placed all around the key tie down points and comes with tennis balls (to cover the tops of your stanchions). This cover should last a lot longer than poorly fitted generic tarps.
|
Upgrade aluminum tanks designed specifically for the 26M. These tanks offer an increased range of about 40% over the standard factory 12 gallon tanks and have a mechanical fuel gauge on the top of the tank.
The Moeller LP12 tanks no longer fit, despite the dimensions seeming to be correct on the packaging. This is a known issue and we have yet to find one of the LP12s that will actually fit anymore.
The tanks will need to be grounded to the negative post on the battery. An optional ground wire kit is available.
Optional fuel connectors are also available for Honda, Mercury, Johnson/Evinrude, Nissan/Tohatsu, Suzuki and Yamaha motors.
The optional gas tank hold down straps are part number 4004-1M0,
The tanks have a fixed shipping cost of $65 per tank anywhere in the contiguous US. Alaska, Hawaii and international shipping may be higher, we will contact you with current rates for those destinations when you place the order.
|
Also called BINNACLE table for 26M. Polished stainless hoop binnacle guard, with hardware for the table. Has hinge up white plastic table with hardware. PLEASE SPECIFY PEDESTAL STYLE - EITHER STAINLESS POLE W/FIBERGLASS TOP OR FULL FIBERGLASS PEDESTAL. This table folds down or can be removed by simply pulling the quick pin! For more fun add a wine glass holder or one of our double cup holders to the rail!
Wine glass holder found here.
Drink holder found here.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Side boarding ladder slides onto genoa tracks, easily moved from one side to the other by just sliding the ladder off and then onto the other track, or you can leave the brackets on the track and remove the ladder by pulling the quick pins. This is a nice addition to your 26M or 26X, this is very popular!
We will combine shipping when we can on this item but often times the ladder must ship separately due to its odd size/shape.
Starting April 2019 the step treads on the ladders are now a light grey, as seen in the last two photos. White step treads are not available right now. The pictures showing the white treads are just to illustrate the use of the ladder.
We sometimes run long back-orders on this item, up to about 6 weeks, so please order far ahead of time.
|
This is the stock system for 2005 and newer 26M. Can be retrofitted to 2003 and 2004 26Ms. For any boats other than 26M, please use part #3418-1V0 found here. Please provide a hull ID# in the "comments" section when placing an order. Because of liability we cannot sell this kit for anything that is not a MacGregor or Venture boat. Kit includes everything you will need for installation on any 26M model.
If you have an early 26M with the older block and tackle style mast raiser and want to upgrade to the winch style, order our retrofit kit, part #3464-1V4.
Ships in two packages.
|
A pair of stainless grab handles to hold on to when exiting the 26M or Tattoo 26 companionway. Once you have these installed you will ALWAYS reach naturally for them to steady yourself when going up the ladder. The area is very strong where these are installed. Includes mounting hardware.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This kit includes all the parts you will need to convert an existing block and tackle style mast raiser to the newer winch style. You will need a good mast raising pole with all of its standard hardware and your existing side support wire assemblies to make this kit work. If you do not have a good pole order the complete kit, part #3418-1M0 for the 26M or #3418-1V0 for all other MacGregor or Venture boats.
Installation of this kit requires that you drill 2 new holes in the mast raising pole to mount the winch and 1 hole in the mast for the mast raising bail.
|
Sunbrella canvas with screen mesh front.
NO LONGER AVAILABLE
|
Sunbrella cloth storage organizer that attaches to a wall or bulkhead with velcro. Has pockets for cups and larger pockets for plates or paper towels. This is a nice convenient way to stow those difficult galley items. Stocked in black. Other colors special order and non refundable.
PLEASE CALL IF YOU'D LIKE A COLOR THAT IS NOT LISTED. COLORS CAN BE FOUND ON THE SUNBRELLA CANVAS WEBSITE.
LINK HERE-- Sunbrella Canvas Colors
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sunbrella cloth storage organizer that attaches to a wall or bulkhead with Velcro. The top portion is mesh with elastic pocket for small items, chapstick, fingernail clippers, etc. The other pockets are great for TP, sunscreen, and general stuff!
PLEASE CALL IF YOU'D LIKE A COLOR THAT IS NOT LISTED. COLORS CAN BE FOUND ON THE SUNBRELLA CANVAS WEBSITE.
LINK HERE-- Sunbrella Canvas Colors
All colors other than black are non-refundable.
|
Fills the space underneath the captains chair to cut down on noise and also keep items from sliding away and into the engine well. Installs with included stainless screws. You will also want some marine sealant to seal the screw holes. This is only meant for 26M. The 26X panel is part number 4908-1X0
|
Fits all 26M. Early boats used a different style pelican hook. Will not match cosmetically. If boat is equipped with stern rail seats, Lifeline will need to be shortened and re-crimped, sold as each.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fits all 26m except early models with 2 loops on top of aft cabintop stanchion. THE FORWARD ATTACHMENTS CHANGED OVER THE YEARS. PLEASE SPECIFY WHAT YOUR FORWARD ATTACHMENTS CONSIST OF.
|
This bright red cover fits Suzuki 50/60/70 3 blade props. Has reflector strip. Improves safety on the highway and protects the prop from minor damage. Used for trailering only.
|
Can be used for swim ladder grab handle on 26X or 26M, use screws and 3M5200 to attach. Can be used elswhere on other boats but may need to be through bolted.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fills the space underneath the captains chair to cut down on noise and also keep items from sliding away and into the engine well. This is the PANEL ONLY, you will not receive the brackets or mounting hardware. This is only meant for 26M. The 26X panel the brackets included is part number 4908-1X0
|
There are two sizes available for this cup holder. It can mount to any vertical rail or stanchion and can be used as a single drink holder, or it folds out for two! Easy to install and remove with just a screwdriver. The available rail sizes are 1" and 7/8". Most MacGregor Stanchions and 26M stern rail seats are 1" the Blue Water Yachts Pedestal Guards will be 7/8" except for the 26X Cockpit table which is 1". To be sure you need to measure the rail you want the cup holder to fit! Just put a tape measure behind it and look on both side to line it up, it should be easy to tell which you have.
|
Used for jib sheets or furling control line on most macgregors, not factory standard, will match factory mounting holes, but will not match cosmetically. Older boats used a variety of cleat styles, to match 1995 and newer boats exactly, use part # 4202-1V0. These cam cleats hold lines securely and release instantly for easy, precise trimming. Multiple rows of high-load ball bearings to reduce friction and V-shaped line entry allow cams to open easily for snap-down, rather than draw-through, cleating.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This kit includes a new gasket and 6 self sealing bolts. Replaces the gasket under the fuel gauge/fuel pick up fitting on older Moeller and Tempo, 9 and 12 gallon tanks.
|
USCG Approved Type III PFD
• Durable nylon outer shell; poly-twill inner • Adjustable belts and chest strap to keep vest from riding up • Lightweight, durable flotation foam • Open-sided styling
|
Sailing Gloves in red, black, or blue. Colors cannot be specified as we get what we get! Leather palms and top of fingers with elastic fabric back. Choose Sm, Med, Large, or XLarge.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This replaces the 3/8" bolt at the mast base with a pin without any threads. This makes it slide in and out much easier. One end of the pin has a ring welded on it and the other has an easy to remove split pin. On the 26M we occasionally find rough spots inside the mast base plate tube that will need to be filed down with a round file to use this pin.
|
This wine glass holder can mount to any vertical rail or stanchion. Easy to install by snapping it on and off the rail, or install with the supplied retainer hoop for a more permanent mounting. The available rail
sizes are 1" and 7/8". Most MacGregor Stanchions and 26M stern rail
seats are 1" the Blue Water Yachts Pedestal Guards will be 7/8" except
for the 26X Cockpit table which is 1". To be sure you need to measure
the rail you want the cup holder to fit! Just put a tape measure behind
it and look on both side to line it up, it should be easy to tell which
you have.
|
This is a much easier and less frustrating pin to use for attaching the headstay (or furler) to the bow chain plate. It is 1 1/2" long and has about a 1" head, so it is easy to hold/handle. Some headstay turnbuckles have a metric hole (6mm) which will need to drilled out just a little to 1/4" size, this takes just a minute. NEVER USE A STRAIGHT QUICK PIN OR "BALL LOCK" TYPE PIN ON YOUR HEADSTAY. THEY WILL FALL OUT AND YOUR MAST WILL COME DOWN!!
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This all stainless steel locking pin allows for an easier solution than the 1/4" bolt that held the boom to the gooseneck, or the bolt that holds the mainsail into the tack bracket.
Depending on your mainsail tack configuration it can be used in two different ways:
If your mainsail tack attaches to a "U" shaped bracket on top of the bolt that holds the gooseneck tube to the mast bracket then you can use this as the tack pin that goes horizontally through the "U" bracket. In this configuration it will not work to replace the vertical bolt through the mast bracket as the sail pulls upward on that bolt.
If your mainsail tack attaches to the front end of the boom using a clevis pin through the sail track (the way most MacGregors should be if rigged they have had slides added to a factory mainsail) then you can use this pin to replace the vertical bolt that attaches the gooseneck tube to the mast bracket making it really quick and easy to remove the boom.
|
Replace canvas attachment screws with this easy to remove quick pin. 1/4" diameter x 1" length. The canvas mounting "feet" will need to be drilled out to 17/64" to use these pins. Do not use for rigging or forestay pin.
|
Not sure what MacGregor parts to get for someone? Give the open ended gift of a Blue Water Yachts gift certificate. They never expire and are good for anything in our online store! Let us know how much you would like for your certificate and we can make it out for any price.
|
|
|
|
|
|
|
|
|
|
|
|
|
A fully equipped MacGregor can easily become a project to rig if you don't have your boat set up properly for easy rigging. This kit can cut rigging time in half for some boats, and reduces frustration levels by more than that!
Below is our recommendation for what we would put in a complete quick rig kit, but you can customize it however you want. - 4 stainless steel snap shackles to add to the bottom of your mainsheet, boom vang, and mast raising kit, as well as on your jib halyard where it attaches to the top of the mast raising pole. We recommend 1 swivel snap shackle and 3 fixed. - 2 easy to hold headstay pins (yes, you even get a spare) so that you don't have to struggle with the tiny clevis pin to attach your headstay to the bow. A word of warning: NEVER use a quick release or ball-lock pin for your headstay! They WILL fall out causing your mast to fall! - 8 1/4" x 1" quick pins. These are great replacements for the screws at the mounting bases for dodgers and biminis, as well as lots of other applications for 1/4" bolts. A bimini will require 2 quick pins and a dodger will require 6. - A pelican hook for your Starboard forward lifeline. This allows you to release your lifeline quickly and easily while trailering so that you don't need to tuck the spreaders under the lifelines. You will have to borrow a heavy duty Nicopress tool to crimp these, or you can send your lifelines to us and we can do it for you.
- 2 mast base quick pins. These take the place of the 4" or 4 1/2" bolts that secure the mast base plate to the deck plate, or the mast to the deck plate depending on which boat you have. You can put away the 9/16" wrenches if you get one of these, no more struggling with those nylock nuts and bolts. We recommend 2 just because it's nice to have a spare.
|
|
|
