Home > MacGregor Boat Parts > MacGregor 26M (2003-2013) > Sails > Spinnakers
Sort By:
Page of 1
SPINNAKER, CUSTOM SPINNAKER, STANDARD REPLACEMENT SPINNAKER SLEEVE
SPINNAKER, CUSTOM
Our Price: $1,199.00
SPINNAKER SLEEVE
Our Price: $329.00
.75 OZ NYLON, FULL RADIAL, CHOOSE YOUR COLORS

The same design as the standard spinnaker, but made to order in your choice of colors
Does not include sheets.

This is a custom product which typically takes 6 weeks to deliver.
.75 oz NYLON / FULL RADIAL DESIGN, RED/WHITE/BLUE.

A full-radial sail pattern, very cool looking! The price is for the sail alone. You will need sheets, tack hardware, and halyard. We recommend raising your existing halyard if you have roller furling for you headsail, or installing a new halyard 16-24" above your current headstay. This allows the sail to fly with less interference with the headstay and headsail. On the 26M a bow sprit is a nice way to also get less interference with the headstay.
Venture 24/224, Venture 25, MacGregor 25, 26C & 26D requires halyard to be raised 24" above headstay. See our Spinnaker Halyard Relocation Kit to raise the halyard. Part number #3807-1V4

Does not include sheets

Also known as a dousing sock or a spinnaker sock. Light grey in color.
Considered the best dousing sock on the market. High quality breathable material. Tangle resistant design. Kevlar funnel, slips easily over spinnaker. Works much better than less expensive designs with a wire hoop.
WHISKER POLE, HEADSAIL SPINNAKER BOW SPRIT "ADD A HALYARD" SPINNAKER KIT
WHISKER POLE, HEADSAIL
Our Price: $179.00
SPINNAKER BOW SPRIT
Our Price: $169.00

We recommend this telescoping pole (6'-12') for all Macgregor models. While Forespar says to use a larger size, we have found that the larger pole is too heavy to use in light wind without the complexity of a pole lift line. An added benefit is that if you completely lose control of things in a big blow, the plastic end fitting will break, acting as a sort of "fuse". These fittings are inexpensive and easy to replace. We stock these poles with latch fittings on both ends as we have found the "spike" style poles tend to come out of the sail grommet if the sail shakes a lot or goes slack. Instead latch securely onto the leeward sheet.

Everything is included in this kit for all boats except for 26M. If you have a 26M you must add the additional mast padeye bracket.

Because of the length this item ships oversize, and is subject to an additional $25 shipping charge. If we are able to get a cheaper shipping rate we will manually adjust your invoice accordingly.


This bow sprit is for the 26M, only. This is to help keep the spinnaker out in front of the headsail. The bow sprit comes with hardware to add to your anchor roller, which serves as the base for the bow sprit. Comes with mounting hardware, control line and blocks.

Complete kit for adding a spinnaker halyard. Includes 5/16" 66' halyard line, a mast cleat, and 26M upper mast tang with block. Mount mast tang 18"-24" above headstay.  Also includes all stainless mounting hardware. If you have any boat older that is not a 26M or Tattoo 26, please use part #3810-1v4
EXTENDED ANCHOR ROLLER SPINNAKER HALYARD RELOCATION KIT SPINNAKER HARDWARE KIT
EXTENDED ANCHOR ROLLER
Our Price: $95.00
SPINNAKER HARDWARE KIT
Our Price: $45.00

Extended anchor roller, usually mounts opposite side of the chain plate, like the factory anchor roller. Gives you a place to hang your anchor while using the factory roller to mount a spinnaker bow sprit. Also, the extra length may make it easier to hang a plow anchor. Includes mounting hardware, you will also need 3M5200 sealant. This anchor roller is 3 inches longer than the factory anchor roller. Be aware that some plow anchors may not fit under the Roller Furling Units. Be sure to measure the height of the anchor before you purchase.

Used to relocate the spinnaker halyard a recommended 18" to 24" above your headstay for flying an assymetrical spinnaker. Includes nuts and bolts.

Tack pennant, to help keep your spinnaker flying out in front of the bow rail, and two small turning blocks for the spinnaker sheets. The two small blocks attach to your stern rail cleats. Works best on stainless cleats, if you have the black plastic cleats you will need to add a small loop of line through the middle of the cleat to attach the turning blocks to. By sheeting all the way to the stern cleats on your boat you will insure proper sheeting angles for sailing performance.

Gift Certificate

Not sure what MacGregor parts to get for someone? Give the open ended gift of a Blue Water Yachts gift certificate. They never expire and are good for anything in our online store! Let us know how much you would like for your certificate and we can make it out for any price.


   
 
Sail Buying Guide