|
|
|
|
|
|
|
|
|
|
|
|
|
Now available again, CDI is under new ownership and back in production.
This is the complete roller furling system for all MacGregor models. You will also need the deck hardware to lead the control line to the cockpit and a headstay compatible with the furler. We can provide you with both. Your headstay must have a standard turnbuckle at the bottom and a swaged threaded stud on the bottom end of the wire, not a loop. The luff is not returnable.
The ball bearing upgrade does reduce friction when furling the sail, but also adds some maintenance, while the standard bearing is maintenance free.
|
Fits V21, V22, V222, V23. Does not have sail feed slot cut or any holes for hardware drilled. Must be shipped motor freight, call for quote, disregard quoted shipping on website. Masts are shipped in 2 pieces with a splice / reinforcement piece at the spreaders. Mast packaging fee: $150
Select appropriate options if you'd like the mast drilled for hardware installation and/or notched for the sail feed slot.
We recommend buying a new mast foot plate with a new mast so we can drill the holes to match up correctly.
|
THIS LUFF FITS THE CDI UNIT ONLY. This is the plastic headfoil for the CDI, Cruising Design, roller furling units. This plastic luff is what the headsail rolls up onto, the headstay is inside. Has two groves, one on each side, for sail. Luff is not returnable.
In some cases the shipping charge may be higher than the estimate. We will contact you if this happens.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This boom fits all Venture and MacGregor models through 1987 except the V-24 and V-224 (these boats had an 11' long boom which is no longer available). We will cut to length for models with boom lengths under 10'. Must be shipped motor freight, expect high shipping charges and a $30 special packaging fee. The original size boom section is no longer available. We are using the same section as the mast, this will require that you also replace your boom end caps with the new part, boom end cap large. Please call if you have questions.
|
Replacement plastic drum assembly for the CDI FF2 roller furling system. This does not come with the luff support pin, or the anchor pins/shackles that are pictured. All of those parts are available separately.
For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #2010 or "B" in the diagram.
|
This is the newer winch style mast raising system for use on all MacGregor and Venture boats except the 26M. This system can be used if you don't have a mast raiser at all or if you want to update a block and tackle style system to the newer winch style.
Most boats will need some additional hardware, especially if you don't have any mast raiser at all now. Be sure to read the "Extended Information" section before you order! If the wrong parts are ordered from the drop-down options the customer will be responsible for return shipping charges and the shipping of the correct parts.
If you have an existing block and tackle style mast raiser and want to upgrade to the winch style, order our retrofit kit, part #3464-1V4
This system is very specific to the MacGregor Mast and MacGregor hardware and is not sold for or intended to be used on other brands of boats.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fits all boats except V24 and V224 which had an 11' boom, we can offer this length. This will need to be cut to length for all models 17' thru 24'. Must be shipped motor freight, expect high shipping charges and a $30 special packaging fee. We are using the same section as the mast, this will require that you also replace your boom end caps with the new part, boom end cap large. Please call if you have questions
|
Backstay tensioner kit for M19 and all keel boats with the 24' tall mast. Attaches to existing female shroud adjuster at stern chainplate, if your female adjuster is missing, you should order that also, part #3102-110.
|
This kit includes all the parts you will need to convert an existing block and tackle style mast raiser to the newer winch style. You will need a good mast raising pole with all of its standard hardware and your existing side support wire assemblies to make this kit work. If you do not have a good pole order the complete kit, part #3418-1M0 for the 26M or #3418-1V0 for all other MacGregor or Venture boats.
Installation of this kit requires that you drill 2 new holes in the mast raising pole to mount the winch and 1 hole in the mast for the mast raising bail.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This kit gives you all the blocks, line and hardware to install a Boom Vang on any Mac except the 26M (use kit 3301-1M0). Does not work with early boats equipped with the roller reefing boom when the sail is actually reefed. Most boats already have the holes drilled in the mast and boom for the attachment bolts. If yours does not, you will have to drill two 1/4" holes.
|
This is a replacement metal ball bearing for the FF2 furling unit. Although it's not a "night and day" difference between the standard bearing and the ball bearing, it is a nice upgrade and truly the only way to get maximum performance and ease of use out of the CDI flexible furler system.
If you're having trouble with rolling and unrolling your furling unit we suggest first looking at replacing the furler control line. Sometimes the line is too big (should be 3/16") or it's just old and that's why the furler is getting stuck. If your line is good but you're still wanting a system that rolls more easily, then the ball bearing upgrade is probably worth it.
For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is part "E" in the diagram.
|
Replacement halyard top fitting for the CDI FF2 roller furling system.
For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #2011 or "J" in the diagram.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
New style plastic replacement cup for the CDI FF2 roller furling system, the Stainless cup is no longer available (new picture coming soon). This is the cup only, the main plastic bearing is a separate part.
For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #1807 or "F" in the diagram.
|
This is a great upgrade for any older boat with loose spreaders that can fold up against the mast. Greatly improves both the strength and stiffness of the rig, making it much easier to get good headstay tension. Improved headstay tension means improved upwind performance. Fits 3.5" X 4" teardrop style mast (1967 thru 2003). Most 26X models came with rigid spreaders standard, some early boats did not.
|
This kit modifies the boom so you can reef the sail from the cockpit. Your mainsail must have slides and jacklines, or slides and a mast gate cover to work properly. With just slides and no jacklines or mast gate cover, you will need to remove 1 or 2 slides from the mast to reef. Works great with your halyards led aft to the cockpit. An easy way to update your old roller boom to a more modern system.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Aluminum pole only, no winch or hardware. Fits all boats with mast raising system except very late model M25 and very early 26C, which had a 9' pole. THIS POLE IS no longer available. These boats should be converted to the new 6' pole. Mast Raising System poles may not be available. Call for information. Ships by itself.
|
Kit for cleanly running your roller furling line back to the cockpit. Includes 45' 3/16" line, four fairleads (like the two shown), and a cam cleat to mount on top of the deck. Hardware will depend on which boat you have, please let us know the year of your boat. The CDI Roller Furling Kit does not include this. But, if you are adding roller furling to your boat to be able to control the furling from the cockpit is a must!
|
Replacement halyard line for the CDI FF2 roller furling system. This is a special line that is pressed with a fitting on the end and then de-cored. It is not just normal yacht braid.
For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #1932 or "K" in the diagram.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/8" 1X19 stainless steel wire on all Mac 23ft and smaller. 5/32nd 1X19 stainless steel wire on 24ft to 26ft models. The end fittings vary on each boat. You must send in old shrouds so we can match the measurements and make sure everything has orginal factory hardware.
|
Replacement fixed spreader sockets only, THIS PART NUMBER DOES NOT COME WITH THE SCREWS AND BOLT TO ATTACH IT
|
1/8" 1X19 stainless steel wire. You must send in your old shrouds so we can match the measurements and make sure everything has original factory hardware.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 x 19 - 1/8 IN Stainless Steel wire. These are made to order for your boat. works with roller furling or hank on sails. *YOU MUST SEND US YOUR OLD STAY TO MATCH FACTORY MEASUREMENTS.*
|
1/8" 1X19 stainless steel wire. Found on all Mac 23ft and smaller and 5/32nd 1X19 on 24ft to 26ft models. The end fittings vary on each boat model. You must send in old shrouds so we can match the measurements and make sure everything has orginial factory hardware.
|
Current style used on the 26M. Boats older than 1997 need to update to new boom end cap (3405-111) also.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement main plastic bearing for the CDI FF2 roller furling system. This is the bearing only, the stainless cup is a separate part number.
For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #1033 or "E" in the diagram.
|
1/4" turnbuckle with a threaded stud and toggle at both the top and bottom. Fits headstays with loops on both ends of the headstay. Used for hank on sails.
|
This little red wind vane sits at the top of your
mast helping the skipper sail and look like a pro while sailing. This shows the direction the wind is coming from, helps you sail close to the wind and properly sheet your sails when off the wind.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This item was not a standard item on any MacGregor model but
can be used on the Genoa tracks of many models. These are NOT intended to
replace the standard genoa cars, but rather to be placed at the aft end of the
track to allow the driver to easily cleat off the Genoa or Spinnaker sheets in
lighter wind conditions that do not require the winches to be used.
Spinnaker sheets can be run directly to these cars in light to medium wind.
These cars fit all MacGregors , Venture and Tattoo models
that have standard 1” aluminum T-Track, some older model boats had smaller 7/8”
stainless steel or aluminum track, these will not fit those tracks.
|
1/8" 1x19 Stainless Steel wire with a loop at each end. Different models and years used different lengths. You will need to measure your forestay from loop to loop (the inside or "load bearing" face of the loop) or, better yet, send in old headstay and turnbuckle for us to match it up exactly.
If you are ordering a new turnbuckle also (part #3107-000), then measure from the inside face of the loop at the top to the center of the hole where the turnbuckle pins to the boat at the bottom with the turnbuckle set about 1/3 of the way closed. If you have questions, please email or call for more info, you don't want to get a new forestay that doesn't fit!
|
This mast base is approximately 4" tall and has a long vertical slot in each side for the mast base bolt. Used on all keelboats as well as a few M19s and 26Cs in 1992 and 1993. Can be upgraded to newer hinged style mast base by using part #3438-1X0 znd 3439-1X0.
|
|
|
