|
|
|
|
|
|
|
|
|
|
|
|
|
Used for M19, 26S (1992-1995), 26X, 26M, and Tattoo boats. Sold only in 50' sections. This is very difficult to install and we recommend a professional to do the install work. Needs to be stretched very hard for proper installation so 50' is plenty to do the whole boat.
This kit also includes 2 fiberglass end caps and 3 cartridges of 3M 5200 Marine Sealant (in caulking gun style tubes), as well as 1 cartridge of 3M 4000 UV, which is applied over the top edge of the rubrail where the rubber meets the boat. This should be enough to reseal the new rubrail all around the boat.
Used only on boats 1992 and newer. We do not have the older style rubrail available.
|
Used for M19, 26S (1992 -1995), 26X, 26M, and Tattoo boats. Sold only in 50' sections. This is very difficult to install and we recommend a professional to do the install work. Needs to be stretched very hard for proper installation so 50' is plenty to do the whole boat.
Used only on boats 1992 and newer. We do not have the older style rubrail available.
|
Rectangular center valve, was deleted in mid 1997, newer boats have transom mounted valve ONLY.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
26X mid 1997 and later. Fits all 26M
|
Fits all M19 and 26X thru mid 1997, Newer 26X and 26M use 3" valve. This valve comes with a plastic handle installed on it. Metal handles can be purchased separately with part H206-110.
|
Replacement handle for ballast tank center valve used on 26C and early 26X. Looks like a huge wing nut.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
White plastic cap to cover aft end of rubber rub rail. Only used on boats 1992 and newer. The original version was white fiberglass, replacements are black thermo-formed plastic. Sold by the pair.
|
Early 26X only, small round (top) and large rectangular (bottom) gaskets.
|
fits 26x with 3" valve
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fits early 26x with 1 1/2" valvue
|
Used anywhere you want an easily removable weather tight access point. Often used to access fuel fill caps on 26X.
Use 4 3/8" Hole saw and 3M5200 Marine sealant
|
Round rubber seals for 3" transom valve, Valve must be removed and reinstalled to replace seals. This is a replacement set of 2 seals.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A rubber cable boot and mounting ring, sold together as a pair. This is a 3" diameter ring and can be mounted anywhere on the hull or transom, it is recommended that you use a marine sealant along with stainless screws when mounting this piece. Typically used with steering cables/controls or electrical wires.
|
Black and white MacGregor name sticker. Rectangular shaped. Used on all the older boats and trailers.
|
Dipstick tube to measure how much water is in your ballast tank.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Metal screw on handle for all transom valves. does not include extension rod. This handle is stronger than the plastic handle (H206-114) but not as corrosion resistant in salt water.
|
Standard air vent plug in brass. Air vent plugs are only made in one size, they are adjustable! Hold rubber plug end and twist clockwise on the ring, this makes the rubber fatter to fit the hole size.
|
This handle is not as strong as the metal handle (H206-110) but is totally corrosion resistant. If you keep you valve properly lubricated so it moves fairly smoothly this handle will outlast the stronger metal one in a saltwater environment.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
small round rubber seal for 1 1/2" transom valves
|
Not sure what MacGregor parts to get for someone? Give the open ended gift of a Blue Water Yachts gift certificate. They never expire and are good for anything in our online store! Let us know how much you would like for your certificate and we can make it out for any price.
|
|
|
