|
|
|
|
|
|
|
|
|
|
|
|
|
Fits all boats from 1982 - 1995 except the 26X. Due to many variations from boat to boat and year to year, these rudders are shipped without the pivot bolt holes drilled. match up to your old rudder or bracket to drill.
This new high performance replacement rudder blade fits most 21, 22, 25, 26S, 26D with a 1.75" rudder castle opening. This rudder blade is a drop-in replacement for your boat's original blade, no modifications to your boat are necessary. Constructed of HDPE hard plastic. This rudder blade helps reduce weather helm and tiller effort. The true NACA airfoil shape maximizes lift while reducing drag, making it faster off the wind, with more control. The lift generated will help the boat point higher, and allow your boat to accelerate in puffs without rounding up.
PLEASE NOTE THAT HDPE BLADES 6-8 WEEKS TO HAVE MADE
This item uses $50 flat rate shipping, shown at checkout for domestic shipments. If this is shipping international it will probably not show the correct rate and we will have to contact you with the shipping amount after the order is placed. Canada is usually about $80, other countries will usually be higher than that.
|
This new high performance replacement rudder blade fits most 21, 22, 25, 26S, 26D with a 1.75" rudder castle opening. This rudder blade is a drop-in replacement for your boat's original blade, no modifications to your boat are necessary. Constructed of fiberglass and laminated with vinylester resin, molded with an NACA airfoil shape and finished with white gel-coat. This rudder blade was designed to reduce weight compared to our HDPE rudder blade, while also helping reduce weather helm and tiller effort.
Match up to your old rudder or bracket to drill. These rudders are fiberglass, made with an improved airfoil shape. 1 year warranty is extended to the original boat owner.
This item uses $50 flat rate shipping, shown at checkout for domestic shipments. If this is shipping international it will probably not show the correct rate and we will have to contact you with the shipping amount after the order is placed. Canada is usually about $80, other countries will usually be higher than that.
|
Black anodized aluminum. Used on all boats from 1982 thru early 1990 except M21, which used a similar but shorter version.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used on all boats from 1982 thru 1989, some early 1990 models had external rudders and used this part, later 1990 models used internal rudder post.
|
Heavy stainless steel piece used to connect the tiller to the rudder post on boats with the internal stainless steel rudder post.
|
Used to secure the lower end of the stainless steel rudder post on late model 26C.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Delrin shear pins for rudder hold-down applications. These are designed
to be sacrificial, they hold the rudder completely in a down position
unless an underwater obstacle is encountered at speed.
For example, the Macgregor rudder assemblies require approximately 150
lbs of force on the tip of the blade to shear this pin, much less than
the loads transferred during a grounding, but dramatically more than is
evident while under sail at or above hull speed.
Unlike metal pins or nylon bolts, the delrin construction allows them to
shear completely rather than deform.
|
Thin stainless side plate used between aluminum rudder post and wooden tiller to prevent wear to the tiller handle..
|
A rubber cable boot and mounting ring, sold together as a pair. This is a 3" diameter ring and can be mounted anywhere on the hull or transom, it is recommended that you use a marine sealant along with stainless screws when mounting this piece. Typically used with steering cables/controls or electrical wires.
|
|
|
|
|
|
|
|
|
|
|
|
Not sure what MacGregor parts to get for someone? Give the open ended gift of a Blue Water Yachts gift certificate. They never expire and are good for anything in our online store! Let us know how much you would like for your certificate and we can make it out for any price.
|
|
|
