Home > MacGregor Boat Parts > MacGregor 26M (2003-2013) > Steering
Sort By:
Page of 1
RUDDER BLADE, 26M, CURRENT
Our Price: $299.00
STEERING, RACK AND PINION, TELEFLEX, 8 FT SYSTEM
List Price: $189.00
Our Price: $189.00
Sale Price: $175.00
Savings: $14.00
RUDDER BLADE WITH HOLES PRE-DRILLED. THESE ARE SOLD IN PAIRS

This item uses flat rate shipping, shown at checkout
FIBERGLASS RUDDER BLADE WITH HOLE PRE-DRILLED.

This item uses flat rate shipping, shown at checkout
Used to replace discontinued Detmar steering system on 1998 - 2003 26X and early 26M. Also direct replacement for Tattoo 26 factory system. Much more reliable, smother and less sloppy than original. Requires some cutting on steering pedestal to install. Comes with instructions to retrofit. Includes cable, helm unit (sometimes known as a Blast..ask Cheryl), and bezel kit.

The high performance cable has less play, easier and smoother steering, and will keep the steering tight and responsive for longer. Later model 26Ms that already have a Teleflex steering system can just order the upgrade cable by itself, part #5707-1M4.
Most boats do not have the rudders perfectly alligned from the factory, this adjustable crossbar length crossbar allows you to allign your rudders parallel to each other.  Your rudders will work better and have significantly reduced drag. Some mid production 26M models had a straight bar with slots cut into the ends to fit over the end of the tiller arms, later boats used this bar which fits below the tiller arms.  Use this part to replace either. Early 26 M models used this rudder crossbar with 2 bends in it, later models used a straight bar, check to be sure which one you need.
RUDDER POST, 26M
Our Price: $145.00
STEERING, CUSTOM, 26M
List Price: $149.00
Our Price: $149.00
Sale Price: $139.00
Savings: $10.00
STEERING, RACK AND PINION, TELEFLEX UPGRADE CABLE
List Price: $165.00
Our Price: $150.00
Sale Price: $135.00
Savings: $30.00
Stainless steel rudder post used on all 26M models. You should NEVER sail with the engine connected to the steering, and this BWY kit makes it really quick and easy to connect and disconnect.  Locks engine straight for easy and safe sailing.  Vastly easier to use than the factory system that uses tiny nuts and bolts to connect and disconnect. The high performance cable has less play, easier and smoother steering, and will keep the steering tight and responsive for longer. This is the cable only. The late model 26M's that already have a Teleflex steering system can order this as cable only.

If you do not have a Teleflex steering system you will need to order the full system as a kit.
STEERING, WHEEL, 15 INCH
Our Price: $82.50
USED ON TATTOO 26, LATE MODEL 26M OR LATE 26X BOATS THAT HAVE HAD THEIR DETMAR STEERING SYSTEM REPLACED WITH TELEFLEX STEERING SYSTEM.  DOES NOT FIT EARLY 26M OR 26X THAT STILL HAVE DETMAR. BOATS WITH DETMAR STEERING NEED TO REPLACE THE COMPLETE SYSTEM WITH 5715-1V3 STEERING. 8' LENGTH 15" STEERING WHEEL, FACTORY REPLACEMENT STANDARD SIZE, INCLUDES CENTER CAP. BASIC 26M FACTORY ENGINE STEERING PUSH BAR.  WE STRONGLY RECOMMEND USING OUR CUSTOM STEERING KIT (#5712-1M0) INSTEAD, IT IS MUCH EASIER TO USE.
FITS LATE MODEL WITH TELEFLEX DOES NOT FIT EARLY MODEL BOATS WITH DETMAR STEERING Replacement plexiglass face only for current style 26M steering pedestal. Replacement engine steering arm with quick release ball for custom steering.  Included in custom steering kit.
TILLER ARM, 26M, MID
Our Price: $50.00
MOTOR PUSH ROD, INTERNAL
Our Price: $36.00
WHEEL "BRAKE" FRICTION KIT
List Price: $35.00
Our Price: $35.00
Sale Price: $28.00
Savings: $7.00
MOTOR PUSH ROD ON INTERIOR OF BOAT. Technically not a wheel "brake", this kit mounts behind the wheel and applies enough friction that it acts as a brake. It will not lock your wheel firmly in place during rough conditions, but under normal conditions it will keep the wheel from drifting. Comes with instructions.
USED FOR BWY CUSTOM STEERING, STAINLESS STEEL QUICK RELEASE ASSEMBLY, ALSO REPLACES BRASS QUICK RELEASES USED ON SOME 26X. Plexiglass starboard side panel for current 26M model. USED TO CONNECT NISSAN OR TOHATSU 50HP ENGINES TO STEERING WITH FACTORY MOTOR PUSHBAR OR WITH BWY CUSTOM STEERING
FITS LATE MODEL BOAT WITH TELEFLEX STEERING. DOES NOT FIT EARLY BOAT WITH DETMAR STEERING. Used to secure the lower end of the rudder post on all 26M models. BWY CUSTOM STEERING REPLACEMENT ROD ONLY FOR 26M, NO QUICK RELEASES.
Small angle bracket that attaches the stering cable holder to the side of the boat just above where the cable exits the boat by the engine. Heavy angle bracket with adjustment bolt and attachment bolts for all 26m rudders.  Used to adjust how far forward the rudders go when lowered. Not sure what MacGregor parts to get for someone? Give the open ended gift of a Blue Water Yachts gift certificate. They never expire and are good for anything in our online store.
Complete replacement steering pedestal for current model 26M. Not currently available. NO LONGER AVAILABLE, REPLACE ENTIRE STEERING SYSTEM WITH 5707-1X3.