Home > MacGregor Boat Parts > MacGregor 22 > Rigging
Sort By:
Page of 3
ROLLER FURLING, CDI BOOM, COMPLETE, KEELBOATS MAST RAISING SYSTEM, CURRENT WITH WINCH
ROLLER FURLING, CDI
Our Price: $595.00
BOOM, COMPLETE, KEELBOATS
Our Price: $305.00

This is the complete roller furling system for all MacGregor models. You will also need the deck hardware to lead the control line to the cockpit and a headstay compatible with the furler. We can provide you with both. Your headstay must have a standard turnbuckle at the bottom and a swaged threaded stud on the bottom end, not a loop. The luff is not returnable.

You also may be interested in the ball bearing upgrade for the furling drum. This is a replacement metal ball bearing. ALthough it's not a night and day" difference between the standard bearing and the ball bearing it is a nice upgrade and truly the only way to get maximum performance and ease of use out of the CDI flexible furler system.
This boom fits all Venture and  MacGregor models through 1987 except the V-24 and V-224 (these boats had an 11' long boom which is no longer available).  We will cut to length for models with boom lengths under 10'.  Must be shipped motor freight, expect high shipping charges and a $30 special packaging fee. The original size boom section is no longer available. We are using the same section as the mast, this will require that you also replace your boom end caps with the new part, boom end cap large. Please call if you have questions. Newer winch style mast raising system for updating a block and tackle style system to the winch style. Can be retrofitted to older MacGregor & Venture boats without a mast raiser by adding additional parts.
There are a number of parts you may need to add to the kit depending on your boat. This is very specific to the MacGregor Mast and MacGregor hardware. Not intended or sold to other brands of boats. Please click on "Extended information".


BOOM, BARE EXTRUSION, 10.5 FT ROLLER FURLING, CDI, DRUM ASSEMBLY ROLLER FURLING, CDI, LUFF ONLY
Fits all boats except V24 and V224 which had an 11' boom,  we can offer this length.  This will need to be cut to length for all models 17' thru 24'.  Must be shipped motor freight, expect high shipping charges and a $30 special packaging fee. We are using the same section as the mast, this will require that you also replace your boom end caps with the new part, boom end cap large. Please call if you have questions Replacement plastic drum assembly for the CDI FF2 roller furling system. This does not come with the luff support pin, or the anchor pins/shackles that are pictured. All of those parts are available separately.

For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #2010 or "B" in the diagram.

THIS LUFF FITS THE CDI UNIT ONLY. This is the plastic headfoil for the CDI, Cruising Design, roller furling units. This plastic luff is what the headsail rolls up onto, the headstay is inside. Has two groves, one on each side, for sail. Luff is not returnable.
STAY, BACKSTAY TENSIONER KIT, 24' MAST BOOM VANG KIT, ALL BUT 26M ROLLER FURLING, CDI, BALL BEARING UPGRADE
BOOM VANG KIT, ALL BUT 26M
Our Price: $149.00
Backstay tensioner kit for M19 and all keel boats with the 24' tall mast.  Attaches to existing female shroud adjuster at stern chainplate, if your female adjuster is missing, you should order that also, part #3102-110. This kit gives you all the blocks, line and hardware to install a Boom Vang on any Mac except the 26M (use kit 3301-1M0).  Does not work with early boats equipped with the roller reefing boom when the sail is actually reefed.  Most boats already have the holes drilled in the mast and boom for the attachment bolts. If yours does not, you will have to drill two 1/4" holes. This is a replacement metal ball bearing for the FF2 furling unit. Although it's not a "night and day" difference between the standard bearing and the ball bearing, it is a nice upgrade and truly the only way to get maximum performance and ease of use out of the CDI flexible furler system.

If you're having trouble with rolling and unrolling your furling unit we suggest first looking at replacing the furler control line. Sometimes the line is too big (should be 3/16") or it's just old and that's why the furler is getting stuck. If your line is good but you're still wanting a system that rolls more easily, then the ball bearing upgrade is probably worth it.

For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is part "E" in the diagram.
SPREADER, FIXED BASE, RETROFIT KIT SINGLE LINE REEFING KIT BLOCK, DOUBLE, FIDDLE W/SWIVEL, BECKET, CAM CLEAT, SNAP SHACKLE
SINGLE LINE REEFING KIT
Our Price: $89.00
This is a great upgrade for any older boat with loose spreaders that can fold up against the mast.  Greatly improves both the strength and stiffness of the rig, making it much easier to get good headstay tension.  Improved headstay tension means improved upwind performance.  Fits 3.5" X 4" teardrop style mast (1967 thru 2003). Most 26X models came with rigid spreaders standard, some early boats did not. This kit modifies the boom so you can reef the sail from the cockpit. Your mainsail must have slides and jacklines, or slides and a mast gate cover to work properly. With just slides and no jacklines or mast gate cover, you will need to remove 1 or 2 slides from the mast to reef. Works great with your halyards led aft to the cockpit. An easy way to update your old roller boom to a more modern system.

This block is normally used as lower end of mainsheet block.  Just like the stock block but has a snap shackle for easy removal.
ROLLER FURLING, CDI, STAINLESS CUP MAST RAISING SYSTEM, POLE ONLY 6 FT STAY, FORESTAY, RF, VARIOUS
Replacement stainless cup for the CDI FF2 roller furling system. This is the cup only, the main plastic bearing is a separate part.

For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #1807 or "F" in the diagram.
Aluminum pole only, no winch or hardware.  Fits all boats with mast raising system except very late model M25 and very early 26C, which had a 9' pole. THIS POLE IS no longer available.  These boats should be converted to the new 6' pole. Mast Raising System poles may not be available. Call for information. Ships by itself. 1 x 19 - 1/8 IN Stainless Steel wire.  These are made to order for your boat.  works with roller furling or hank on sails. *YOU MUST SEND US YOUR OLD STAY TO MATCH FACTORY MEASUREMENTS.*
ROLLER FURLING, CDI, HALYARD LINE SPREADER BASE, FIXED, PAIR ROLLER FURLING, CDI, HALYARD TOP FITTING
Replacement halyard line for the CDI FF2 roller furling system. This is a special line that is pressed with a fitting on the end and then de-cored. It is not just normal yacht braid.

For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #1932 or "K" in the diagram.
Replacement fixed spreader sockets only, no hardware or retrofit parts. Replacement halyard top fitting for the CDI FF2 roller furling system.

For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #2011 or "J" in the diagram.
FURLER CONTROL KIT STAY, BACKSTAY, CUSTOM GOOSENECK, MAST AND BOOM ASSY
FURLER CONTROL KIT
Our Price: $59.00
STAY, BACKSTAY, CUSTOM
Our Price: $58.00
Kit for cleanly running your roller furling line back to the cockpit. Includes 45' 3/16" line, four fairleads (like the two shown),  and a cam cleat to mount on top of the deck. Hardware will depend on which boat you have, please let us know the year of your boat. The CDI Roller Furling Kit does not include this.  But, if you are adding roller furling to your boat to be able to control the furling from the cockpit is a must! 1/8" 1X19 stainless steel wire. You must send in your old shrouds so we can match the measurements and make sure everything has original factory hardware.
Current style used on the 26M.  Boats older than 1997 need to update to new boom  end cap (3405-113) also.
STAY, UPPER SHROUD, CUSTOM STAY, LOWER SHROUD, CUSTOM BATTEN SET, TAPERED, 3 PIECES
1/8" 1X19 stainless steel wire on all Mac 23ft and smaller. 5/32nd 1X19 stainless steel wire on 24ft to 26ft models. The end fittings vary on each boat. You must send in old shrouds so we can match the measurements and make sure everything has orginal factory hardware.
1/8" 1X19 stainless steel wire. Found on all Mac 23ft and smaller and 5/32nd 1X19 on 24ft to 26ft models. The end fittings vary on each boat model. You must send in old shrouds so we can match the measurements and make sure everything has orginial factory hardware.

Thin & soft at the forward end, these help keep the sail from "folding" at the front end of the batten.  Improves sail performance, especially in older sails.  Must use as a set.  A nice improvement for not much more money.  Fits all pre 26X (1995) models with stock mainsail.  If your sail has been modified or replaced, it could be different, be sure to check
ROLLER FURLING, CDI, MAIN BEARING BLOCK, DOUBLE, HALYARD LIFT MAST STEP, ONE PIECE, VERTICAL SLOT
Replacement main plastic bearing for the CDI FF2 roller furling system. This is the bearing only, the stainless cup is a separate part number.

For more detailed information on the replacement parts see the CDI FF2 Manual by following this link. This part is CDI part #1033 or "E" in the diagram.
Used in halyards aft kit. Depending on the model of boat, this block is placed on deck at base of mast or is attached to the mast itself. This mast base is approximately 4" tall and has a long vertical slot in each side for the mast base bolt. Used on all keelboats as well as a few M19s and 26Cs in 1992 and 1993.  Can be upgraded to newer hinged style mast base by using part #3438-1X0 znd 3439-1X0.
BLOCK, DOUBLE, STACK CHEEK TURNBUCKLE, TWO TOGGLE WIND INDICATOR, WINDEX AV
TURNBUCKLE, TWO TOGGLE
Our Price: $36.60
WIND INDICATOR, WINDEX AV
Our Price: $35.00
This is a versatile block that can be used in lots of custom rigging projects.  It comes as part of the BWY halyards aft kit for all boats. 1/4" turnbuckle with a threaded stud and toggle at both the top and bottom. Fits headstays with loops on both ends of the headstay. Used for hank on sails.

This wind indicator fits over any standard Shakespeare or Metz antenna. This eliminates the need for a stand-off bracket.

The included tacking angle arrows are not useful on the 26M or Tattoo boats because of their rotating mast.